Renishaw FANUC 31使用中內孔測量程式

yit02yit02

Renishaw FANUC 31使用中內孔測量程式
%
<CEN-4-3>
G91G30Z0
% U$ X  H  X/ `2 |9 y/ [0 n: ~G54
/ I" b% k0 R$ P% F  S6 n5 j- i2 bG90G0X0Y0
G43H01Z100.
(四點測量0度為起點A直徑XY為孔位S為數據指令M安全距離F安全高度)
, z0 u* f' B9 g$ O' }7 wG65P9656A0.R60.X0.Y0Z-5.S0M5.F100.
G0G90X0Y22.5
1 v: w8 S9 F: ?+ m/ n#702=#108
#703=#118
M01
(三點測量90度為起點A直徑XY為孔位S為數據指令M安全距離F安全高度)
G65P9654A90.R60.X0.Y0Z-5.S0M5.F100.
# C+ u% {3 ^+ l8 `G0G90X0Y22.5
9 K, E* R3 U" {+ X$ n#704=#108
6 s0 h% b9 D5 r#705=#118
M01
G91G30Z0
3 i9 ~( I% q: m2 G1 s& z, y: fG90X0Y0
M30
%

#108→實測尺寸
' ^* d* t( P" B: h8 u8 M#118→實測尺寸公差
/ B; h% n) a0 P+ F- w( I0 _

%
O9654(* HOLE MEASURING 3 POINTS)
% o9 k" Z8 q% n$ `  E; @1 EG53
IF[#3008EQ1]GOTO999(PROGRAM RESTART)
#125=#4000(MAIN PRG NO.)
# {2 j8 l) E5 G#126=#4115(MACRO-NO.)
/ W' f* t; e5 {2 x: KM98P9608(AMCS START)
- S7 E8 k# c/ d$ @3 l7 D9 A8 ?#31=-3
* \1 w! l' y' {% `( A! MM98P9615(PATTERN MEASURING)
! I1 ^+ R) v" K) \1 B2 WM98P9609(AMCS END)
M98P9601(HOLE & BOSS DATA)
* S6 L6 s( a( l5 l  R* C6 G5 nM98P9600(PROCESS)
N999M99

1 Q( f+ p' A; U5 v%

4 p7 z$ ^3 U1 T' t7 y  v3 |
/ O8 _2 q( C# A%
O9656(* HOLE MEASURING 4 POINTS)
G53
* y' z- p- k- D# FIF[#3008EQ1]GOTO999(PROGRAM RESTART)
, G0 @- j* `& H" a5 h#125=#4000(MAIN PRG NO.)
#126=#4115(MACRO-NO.)
M98P9608(AMCS START)
6 Y  x2 \5 x8 `9 y7 a#31=-4
& j; J; x7 S0 {M98P9615(PATTERN MEASURING)
1 ?9 o2 n- H4 r; RM98P9609(AMCS END)
M98P9601(HOLE & BOSS DATA)
1 ^2 i& m4 N. e8 M4 tM98P9600(PROCESS)
N999M99

%